Furnace Repair in Richmond, TX
Temper Mechanical Air & Heat repairs gas and electric furnaces for homes in Richmond and across Fort Bend County. We work on attic and closet furnaces, standard and high efficiency models, and every major brand. Most furnace calls get a same day visit, emergency service runs 24/7, and our trucks carry the parts that fail most often, so most repairs are finished on the first trip.
Call (346) 485-8142 or schedule furnace repair online.
- Class A Texas HVAC license, TACLA 92943C
- Texas Master Plumber license MPL 45322 for gas line repairs
- NATE certified technicians
- Written price before any work starts
- Diagnostic fee credited toward your repair
Request Your Furnace Repair
Tell us what your furnace is doing and any error code you see. We will call you back to set up a visit, usually the same day.
- Written price before any work
- Safety check on every visit
- 24/7 emergency line
How a Gas Furnace Starts, and Where It Breaks Down
Every time your thermostat calls for heat, a gas furnace runs through the same sequence in about a minute. If any step fails, the furnace stops and waits. Knowing the sequence makes it much easier to understand what's wrong.

| Step | What happens | If it fails, you'll notice |
|---|---|---|
| 1. Call for heat | The thermostat signals the furnace control board | Nothing happens at all. Check the thermostat, power switch and breaker |
| 2. Inducer motor starts | A small fan pushes old air out through the flue | Silence, or a humming or grinding sound from the furnace |
| 3. Pressure switch proves the draft | A safety switch confirms the flue is clear | The inducer runs, but the furnace never lights |
| 4. Igniter heats up | A hot surface igniter glows orange, or a spark igniter clicks | No glow, or clicking without a flame |
| 5. Gas valve opens | Gas flows to the burners and lights | The igniter glows, but no flame appears |
| 6. Flame sensor confirms the flame | A metal rod proves the burners are lit | The burners light for a few seconds, then shut off. This is the most common furnace problem we see. |
| 7. Blower starts | The main fan sends warm air through your ducts | Burners run but no air comes out, or the furnace shuts off on high temperature |
When you call, telling us which step your furnace reaches speeds up the diagnosis.
Read Your Furnace's Error Code Before You Call
Most furnaces made in the last 20 years have a small light on the control board that blinks a code when something goes wrong.
- Look through the small window on the furnace's lower panel, or check the panel itself, without removing it while the furnace is powered.
- Count the blinks. Many boards flash a pattern, like 3 blinks, a pause, then 3 blinks again.
- Find the code chart, which is usually a sticker on the inside of the furnace door. Take a photo of it.
- Tell us the code when you call, or text the photo.
One tip: don't keep switching the furnace off and on. Many furnaces lock themselves out for about an hour after a few failed tries to light. Repeated resets can clear the error code we need to see, and they can stress parts that are already failing.
The Furnace Repairs We Make Most Often
| Part | What you notice | What we do |
|---|---|---|
| Flame sensor | Burners light, then shut off within seconds, again and again | Clean or replace the sensor and check the flame and ground connection |
| Hot surface igniter | No orange glow, so the furnace never lights | Replace the igniter and check the voltage feeding it |
| Pressure switch or hoses | The inducer runs, but the furnace won't light. Often a pressure switch error code | Clear blocked hoses, ports or the condensate trap, or replace the switch, then confirm the flue drafts properly |
| Inducer motor | Grinding, rattling or humming, then a lockout | Replace the motor and check the flue connection |
| Limit switch | Heat runs for a while, then shuts off as the furnace overheats | Fix the airflow cause first (filter, blower, ducts), then test or replace the switch |
| Blower motor or capacitor | Burners run but little or no air comes out, or a humming sound | Replace the capacitor or motor, and check the blower wheel for buildup |
| Control board | Erratic operation, no power, or no response after a storm or outage | Confirm the board is actually at fault, then replace it and check for the shorted part that killed it |
| Gas valve | The igniter glows, but no gas reaches the burners | Test the gas supply and valve, replace the valve and leak test all connections |
| Rollout switch tripped | The furnace won't run, with a rollout or flame error code | Find out why flames rolled out (a blocked flue or a cracked heat exchanger) before resetting anything |
If a rollout switch has tripped, don't reset it and keep running the furnace. It usually means exhaust isn't leaving the furnace the way it should. See our heating repair page for the carbon monoxide checks we run on every visit.

Attic Furnaces in Fort Bend: What's Different
Most furnaces in Richmond homes lie on their side in the attic, with the air conditioner coil attached to them. That setup affects how they fail and how they're repaired.
- Summer heat ages the electronics. Your furnace sits in a hot attic for months while it's switched off, which wears down control boards, wiring and capacitors before winter even starts.
- Rodents move in. Mice and rats like warm attics and chew through furnace wiring and insulation. We check for damage on every visit.
- Access and safety matter. A proper walkway, a service platform and a working light make repairs faster and safer. We'll point out anything that makes your furnace hard to service.
- Drain pans protect your ceiling. Attic units need a secondary drain pan with a safety switch, because both the AC coil and high efficiency furnaces produce water.
Standard (80%) vs. High Efficiency (90%+) Furnaces
| Feature | 80% furnace | 90%+ high efficiency furnace |
|---|---|---|
| How to tell | Metal flue pipe going up through the roof | Two white plastic (PVC) pipes for air and exhaust |
| Makes water? | No | Yes. It has a condensate trap and drain line |
| Extra failure points | Fewer parts | Clogged condensate traps, drain lines and the pressure switch faults they cause |
Furnace leaking water? On a high efficiency furnace, it's usually a clogged condensate trap or drain line. On any furnace, it can also be the AC coil drain above it. Either way, turn the system off if water is reaching the ceiling, and call us.
Electric Furnace Repair
All electric homes often use an electric furnace or an air handler with electric heat strips, either alone or as backup for a heat pump. Common repairs include burned out heating elements, failed sequencers and relays that don't turn the elements on in order, tripped high limit switches and blower problems. Electric heat draws a lot of power, so breakers that trip during cold snaps are a sign to have the elements and wiring checked. If you have a heat pump, see heat pump repair.
Furnace Repair Cost in Richmond
You approve a written price before we start. For a part by part breakdown, read furnace repair cost in Richmond. Bigger jobs qualify for $100 off major repairs.
| Service | Pricing |
|---|---|
| Diagnostic visitCredited toward the repair | Get a Quote |
| Most furnace repairs (flame sensor, igniter, pressure switch, inducer, blower parts, control board) | Get a Quote |
| Furnace replacement | Get a Quote |
Repair or Replace Your Furnace?
Furnaces in Richmond only run a few months a year, so many last longer than furnaces up north. A clean, well maintained 18 year old furnace can still be worth repairing. Replacement usually makes more sense when:
- the heat exchanger is cracked. It can't be safely repaired.
- the furnace is 15 to 20 years old and needs an expensive part like a control board or blower motor
- you're replacing the AC anyway. The new AC coil sits on the furnace and depends on its blower, so replacing both together often costs less than two separate jobs and gives you a matched system.
We give you repair and replacement prices side by side. See how long furnaces last in Fort Bend, furnace replacement cost and our furnace and water heater replacement guide.
What to Expect When We Arrive
- We check what you already know. The error code, the step where the furnace stops, and when it started.
- We test the whole startup sequence. Thermostat signal, inducer, pressure switch, igniter, gas valve, flame sensor and blower, plus the safety and carbon monoxide checks. See what happens during a furnace diagnosis.
- We show you and price it. Photos of the failed part and a written price. You decide.
- We repair and test. We run full heating cycles to make sure the furnace lights, stays lit and shuts off properly. Here's how same day furnace repair works.
"Terry was very professional and prompt. I learned a lot while he was fixing our furnace for us."
Furnace Brands We Repair
We repair all major furnace brands, including Trane, Carrier, Lennox, Goodman, Rheem, Ruud, York, American Standard, Amana, Bryant and Day & Night. We work on single stage, two stage and variable speed furnaces. As an authorized Trane and Day & Night dealer, we have direct access to factory parts for those brands. If you have a Day & Night Ion system, see Ion system service.
- Trane
- Carrier
- Lennox
- Goodman
- Rheem
- Ruud
- York
- American Standard
- Amana
- Bryant
- Day & Night


Keep Your Furnace From Failing on the First Cold Night
A fall tune up cleans the flame sensor and burners, tests the igniter, clears the condensate trap and checks the heat exchanger before you need heat. Read how to prepare before the first cold front or join an HVAC maintenance plan for yearly service on a schedule.
- Flame sensor and burners
- Igniter test
- Condensate trap
- Heat exchanger check
Furnace Repair Near You
We repair furnaces throughout Richmond, including Long Meadow Farms, Harvest Green, Veranda, Aliana and Pecan Grove. We also serve Rosenberg, Sugar Land (including Greatwood and New Territory), Cinco Ranch, Katy, Missouri City and Fulshear.
Need help with a different type of heat? See heating repair. Heat out on a freezing night? See emergency heater repair.
Furnace Repair FAQs
The most common cause is a dirty flame sensor. If the sensor can't confirm the flame, the furnace shuts off the gas for safety. Weak wiring or poor grounding can cause the same thing. It's usually a quick, inexpensive repair.
Clicking usually means the furnace is trying to start but a step is failing. The usual causes are an igniter that doesn't heat up, a gas valve that doesn't open, or a pressure switch that won't close. Check that the gas valve at the furnace is on, then call us with the error code.
Some handy homeowners do, but it means shutting off power and gas, removing the sensor and handling parts near the burners. In an attic, it's also hard to reach safely. Since we clean the sensor as part of every repair and tune up, most people let us handle it.
High efficiency furnaces produce water, so a clogged condensate trap or drain line is the usual cause. On any furnace, the AC coil drain above it can also overflow. Turn the system off if water is reaching the ceiling, and call for service.
Because furnaces here run only a few months a year, an 80% furnace often makes more financial sense than it would up north. A 90%+ furnace saves more gas, but the savings add up slowly in a mild climate and it has more parts to maintain. We'll show you the math for your home when you're replacing.
Most furnace repairs take 1 to 2 hours once the problem is found. If a part has to be ordered, we tell you how long it will take and how to stay warm in the meantime.
Yes. We repair electric furnaces and air handlers with heat strips, including heating elements, sequencers, relays, limit switches and blower motors.
Yes. Call (346) 485-8142 any time, day or night, if your heat is out on a cold night or you smell burning from the furnace. If you smell gas, leave the home first and call 911 or your gas utility from outside.
Get Your Furnace Running Again
Call (346) 485-8142 or book furnace repair online. Tell us the error code or what your furnace is doing, and we'll come prepared to fix it on the first visit.
Call (346) 485-8142 Temper Mechanical Air & Heat, LLC6115 FM 762 Suite 1200, Richmond, TX 77469 · (346) 485-8142 · info@tempermechanical.comRegulated by the Texas Department of Licensing and Regulation, P.O. Box 12157, Austin, TX 78711 · HVAC License TACLA 92943C · Plumbing License MPL 45322
Prefer to Message Us?
Leave your name, number and a quick note about what your furnace is doing. A real person from our Richmond office will call you back to get you scheduled.
- Same day visits
- Written price first
- 24/7 emergency line